SYSTEM CONFIGURATION
5. Turn the AVR 130 on either by pressing theThe factory default setting for the speaker configura-NOTE: If you choose Logic 7 as the surround
System Power Control 3 on the front panel,tion is to have Osmall� speakers at all positions with amode, the AVR 130 will not make the LARGE
or via the remote by pressing the AVR Selectorsubwoofer installed. If you have this type of Osub/option available for the center speaker. This is due
f or any of the Input Selectors eg39satellite� speaker system, no further configuration isto the requirements of Logic 7 processing, and
on the remote. The Power Indicator 3 will turnneeded and you may skip to the next section.does not indicate a problem with your receiver.
blue to confirm that the unit is on, and the front-
When CENTER NONE is selected, no
panel display will illuminate.With the AVR 130 turned on, follow these steps tosignals will be sent to the center channel output.
configure the speakers:
System Setup6. When SURR SPEAKER appears in the
1. Press the Speaker Select Button 6 35 . WhenLower Display Line ? press the Set Button
The AVR 130 features an advanced memory systemo@.
that enables you to establish different configurationsSPEAKER SIZE appears in the Lower
Display Line ? press the Set Button o@.
for the bass management, digital input, surround7. Press the ?/¤ Buttons n on the remote or
mode and output levels for each input source. This2. When FRONT SPEAKER appears in thethe ?/? Buttons ) on the front panel to select
flexibility enables you to custom-tailor the way in whicheither SURR LARGE, SURR SMALL or
Lower Display Line ? press the Set Button
you listen to each source and have the AVR 130o@ to continue.SURR NONE, using the same guidelines as
memorize those settings. This means, for example,above for Large and Small. When the desired
that you may use different modes or output levels 3. Press the ?/¤ Buttons n on the remote orselection appears, press the Set Button o@.
and trims for different sources. When the Bass
the ?/? Buttons ) on the front panel to select
Management System is set to Independent, you mayeither FRONT LARGE or FRONTWhen SURR SMALL is selected, low-
also set different speaker configurations and crossoverSMALL, as described by the definitions shownfrequency surround-channel sounds will be sent to
points for each input. Once these settings are made,the subwoofer output only. Note that if you choose
they will automatically be recalled whenever you selectabove. When the desired selection appears, pressthis option and there is no subwoofer connected,
the Set Button o@.
that input.you will not hear any low-frequency sounds from
When FRONT SMALL is selected, low-fre-the surround speaker.
The factory default settings for the AVR 130 have all
quency sounds will be sent to the subwoofer out-When SURR LARGE is selected, a full-range
inputs configured for an analog source (except for theput only. Note that if you choose this option andoutput will be sent to the surround-channel outputs,
DVD input, which has the Coaxial Digital Input 1 athere is no subwoofer connected, you will not hearand NO surround-channel signals will be sent to
as the default), Logic 7 Music as the surround mode,any low-frequency sounds from the front channels.the subwoofer output.
when an analog or PCM digital source is in use, all
When SURR NONE is selected, surround
speaker positions set to Osmall,� and a subwoofer con-When FRONT LARGE is selected, a full-
nected. Before using the unit, you will probably wantrange output will be sent to the front-left and front-sound information will be split between the front-
to change the settings for most inputs so that they areleft and front-right outputs. Note that for optimal
properly configured to reflect the use of digital or ana-right outputs, and NO low-frequency signals will beperformance when no surround speakers are in
sent to the subwoofer output.use, the Dolby 3 Stereo mode should be used
log inputs, the type of speakers installed and the sur-
round mode specifics.4. When CENTER SPEAKER appears ininstead of Dolby Pro Logic II.
the Lower Display Line ? press the Set Button8. When S-W SPEAKER appears in the Lower
Speaker
[email protected] Line ?, press the Set Button o@.
These adjustments tell the AVR 130 which type of5. Press the ?/¤ Buttons n on the remote or9. Press the ?/¤ Buttons n on the remote or
speakers are in use. This is important as it adjusts thethe ?/? Buttons ) on the front panel to selectthe ?/? Buttons ) on the front panel to select
settings that determine which speakers receive low-either CENTER LARGE, CENTER
frequency (bass) information. For each of these set-SMALL or CENTER NONE, using thethe option described below that best describes your
system. When the desired selection appears, press
tings use the LARGE setting if the speakers for asame guidelines as above for Large and Small.the Set Button o@.
particular position are traditional full-range loudspeakersWhen the desired selection appears, press the Set
that are capable of reproducing sounds below 100Hz.Button o@.
The choices available for the subwoofer position will
Use the SMALL setting for smaller, frequency-limiteddepend on the settings for the other speakers,
satellite speakers that do not reproduce sounds belowWhen CENTER SMALL is selected, low-particularly the front left/right positions.
100Hz. Note that when Osmall� speakers are used, afrequency center channel sounds will be sent to
subwoofer is required to reproduce low-frequencythe subwoofer output only. Note that if you chooseIf the front left/right speakers are set to FRONT
sounds. Remember that the Olarge� and Osmall�this option and there is no subwoofer connected,SMALL, the subwoofer will automatically be set to
descriptions do not refer to the actual physical size you will not hear any low-frequency sounds fromSUB, which is the OON� position.
of the speakers, but to their ability to reproduce low-the center channel speaker.If the front left/right speakers are set to FRONT
frequency sounds. If you are in doubt as to which LARGE, three options are available:
When CENTER LARGE is selected, a full-
category describes your speakers, consult the specifi-range output will be sent to the center speakerY If no subwoofer is connected to the AVR 130,
cations in the speakersO ownerOs manual, or ask output, and NO center channel low-frequency infor-press the 2 /1 Buttons n on the remote so
your dealer.
mation will be sent to the subwoofer output.that SUB NONE appears in the Lower
Display Line ?. When this option is selected,
16 SYSTEM CONFIGURATION
ACEC
